Safety Sense

50% of crane failure or total collapse is from improper use of outriggers. A pro-active safety approach is using outrigger pads on all set ups. The outrigger pads will displace & reduce the PSI the ground “ sees ” from the point of contact of the outrigger/ shoe/ float/ pontoon on the equipment. The outrigger pads will also remind the personnel at the jobsite to make sure the outrigger system is being used & used correctly. Bigfoot is the first company to manufacture safety orange. This was done to address tripping hazards & make sure the outrigger system is deployed by bringing attention to the operator & other personal on the jobsite.

The outrigger system shall be used according to the manufactures standards.

  • The set up & leveling is critical on any set up or with any style of outrigger system on the equipment. Always follow the manufactures chart on level & grade % allowable for equipment to be set up.
  • Get recent soil conditions. Getting a known ground bearing capacity ( GBC) will help with knowing what outrigger pad is the best fit.
  • Check for located & know where utilities are overhead & underground.
  • Maintain proper clearances on overhead power lines.
  • Outrigger pads shall not be used to bridge any gaps or span over voids.

After the equipment is set up level & according to the manufacture recommendations & with Bigfoot outrigger pads, perform a dry run with spotters. The boom should be run over & around all the outriggers with a spotter not under the boom, but looking at the outriggers. The spotter is looking to see if any of the floats are sinking, shifting or sliding. If there is any issue, stop & stow the boom. Now is the time to re-check the equipment level, improve soil conditions or add Bigfoot outrigger pads & cribbing. There are some great starting points with setting up, but this will not cover all equipment set up. Having a lift director or person in charge on the jobsite to address setting up will help.

  • Knowing the max PSI/ PSF ( this does not factor in shock or impact loading, which is common in DEMO & tree care or removal work. Speed plus mass equals force, this force is measured in PSI/PSF & will go through the outrigger system).
  • Size of outrigger/ shoe/ float/ pontoon on equipment
  • Soil conditions

In many but not all set ups, having this information will address the 3 times the square surface area on grade A soil conditions. The 3 time the square surface area on grade A soil conditions, will displace the PSI from the equipment through the outrigger pad, depending on the GBC value need to be maintained. If there is a known GBC value needed & an engineer has values needed reached, Bigfoot can help.

Cribbing or dunnage should not meet or exceed the height of the base outrigger pad. Example: A 36 X 36 at 2” ( P363620 ) should not have cribbing or dunnage meet or exceed 36” on any set up. The bottom layer or base outrigger pad with be carrying the PSI ( when you see pictures of other outrigger pads with wood cribbing or dunnage underneath or on bottom, the cribbing or dunnage is carrying the load, the top pad is the cushion). Knowing this, the sheer value is need on the set up as well. Bigfoot recommends using the same material to maintain consentient with sheer values, our custom composite is made from the same material as our outrigger pads.

Bigfoot’s American custom composite has no grain lines. This allows the set up of outrigger pads & cribbing exceptionally user friendly. This will eliminate the question on vertical pressure, or out & down outrigger systems, which way should the pads or cribbing face? The sheer value on Bigfoot’s custom composite is the same in either direction. Bigfoots material is not injected or extruded or 100% recycled material, these materials will have different directional shear values & need to be address in addition to set ups. This is another area that Bigfoot has & can help with operators, lift directors or personal in charge. This will without question, using Bigfoot outrigger pads, help with set ups & reduce human error to make sure the hard working personal are using STRENGTH/ STABILITY/ SAFETY on their job sites & equipment.

Ground Bearing Capacities of Various Soil Types
Soil Type (G.B.C.)
Virgin Ground 22 PSI
Asphalt 29 PSI
Compressed crushed stone 36 PSI
Clay/Silt soil, firm 43 PSI
Mixed granular soil 51 PSI
Firm compacted gravel 58 PSI
Firm compacted gravel (more compacted) 72 PSI
Firm compacted gravel (more compacted, class 5) 109 PSI
Brittle weathered rock 145 PSI
Concrete (unknown mix) 1000 PSI

Bigfoot Construction Equipment

is not a vendor or marketing company, but an in house manufacturer with field experience since 1991.
Building with American Materials, with American Veterans since the start of this American Family Business, is exclusive to the
industry and only done by Bigfoot


Strength / Stability / Safety